software

Dean ML 79

I need to extend the hot/ground wires that come from the output jack on a guitar I'm working on. For the insulated wire, can I just solder more insulated copper wire to the end of it to make it longer? And what about the bare ground wire? All I have are a few spools of insulated wire to work with.

I installed a '59 neck humbucker in my mahogany carvin DC127 and its very bright! I'ts also more sensitive to hum (computer monitor, etc) than the bridge Carvin PU. I have to lean further back from the computer to avoid hum. Could I have done something wrong during installation?

The thing sounds KILLER ! Pure vintage tone. It's a Magnatone 440 1x12
combo w/t 2 6V6's and a bunch of pre and a recto tube I never heard of?

I bought new tubes for my Peavy Delta Blues (Sovtex EL84's and 12AX7LPS's) same as it had in it. Do i need to have it biased ? The EL84's are two matched sets is there a special order they are installed in?
Thanks.

Well, two of the 5 anyway. The two main guitars I used are generally my Gamp;L Legacy and Nashville Tele, but these two are kinda interesting...

will the antiquity I and II strat fit a bridge with a string spread of 2-1/4quot;? would the narrower bridge with a spread of 2-1/8quot; be better?

On Saturday i put an Alnico 8 in my mid 80ies SD Custom.
First impression of the A8: dull grey and the biggest pull on the fridge by far. The ceramic (out of the Custom) has a little more magnetic strength on the edge of the fridge than a A5. But the Alnico 8 need about the double strength to pull it off.

Can I wire an SSL52-1b (bridge) and a SSL52-1 RwRp (middle) to humbuck together without too much frequency cancellation or honk? At first glance it looks like it is possible. Is that what the RwRp was designed for? Has anyone tried this? I searched the forum and could find anything on this.

Hi, I'm looking to replace the honky 10quot; 8ohm speaker in my Peavey Envoy. Let me know what you have.

Hey guys.

I plan on installing a set of SSL-1 Vntage staggard pickups in my Mexican Strat (maple fretboard) and was wondering if I should keep the .022uf tone cap or replace it with a .047uf. Thanks!

With all of the high gain amps out there, wouldn't vintage output pickups suffice?

What kind of picks does everyone use? why?

Well, I currently have the Jackson Dinky on credit (I own it, but I'm still paying for it). It's a nice guitar and all, but I'm not sure if it's really quot;mequot;, if you know what I mean. I know the Jackson cult ( ) here will probably push me towards the Jackson, but I discovered a hidden secret. I mean sure, the Dinky has the Sustainiac system (and I've pinpointed exactly which one, too), but if I were to get another guitar I could give in and spend the extra $200, and have a guitar that suits me and my style, along with an awesome feature.

Hey dudes!
Havent posted for a while here!

to replace the allen coils on a Screamin Demon with slug coils --- without destroying the pickup?

I own a Schecter Blackjack 006 guitar with Duncan JB/59n pups and a 5 way switch. Since the tone know doesn't really work I have been planning to get it replaced with one of the right taper value (the dealer who sold it to me said that to cut costs schecter uses the same audio taper pots for both tone and volume which is why the tone works so badly for a lot of them). Since I am doing that I thought that it would be cool to have a push-pull installed to tap the pickups. The only problem is I would like a really complicated setup: I want it tp be the same as it is now with the pot in one position and have only single coil tone modes in the other so right now it is: