software

anyone know a good place to go for a refret in the houston/austin tx area?

Hello All...
I just picked myself up a little B-day present; A PRS Santana/SE Dual HB.

Anybody play one of these? What are your opinions?

The folks where I bought the Invader PUPS have said that the bridge PUP will work fine in the neck position. They also said that Invaders are not made in neck. Any suggestions? I really am not planning on putting the bridge in the neck, will DUncan swap the bridge for a neck?

This is just idle curiosity. Not really thinking of buying one. Has anyone heard, or owned one of these?

Ok, so I'm wiring this Strat pickguard in preparation for my body and neck arriving in a few weeks time. I have two Texas Specials and a Jb Jr (for the Bridge).

i have got to get me one of these!! i think it's going to be my next guitar! Fender John Mayer signature. of course i'll have to swap out the pickups but man that painjob is killer!!
Alder Body

GOOD OR NOT GOOd...Today i went to buy both of SETH LOVER and 59'....seth lover model's neck and 59' model's bridge...i want to know what do you think about my set up...it's correct,isn't it?...i'm not sure..but i want to find my lover sound...i want you to tell me about this set up...and i want to know what do you bore my language?...i want to use Eng language correctly...if you have a time.teach me!!! i'll try...ok? Glad to talk with you...Thank you...bye...

Can someone explain to me, step by step, the process of including pictures with your threads? I can never figure it out.

i need help finding schematics for a hot rails pickup.i'm running hot rails in the neck position,and a kent armstrong hum in the bridge.i have the wiring diagram for the humbucker ,but not for the hot rails.i want to run both pickups straight through,no phasing or spliting.one pickup three way switch to a volume pot.i just need to know what colorerd wire does what.thanx for the help.

MINT original BOx none finer in condition or tone. REally EXPENSIVE!!!!!!!! 300 shipped conus add 3% for paypal respond only to vampirelabs@yahoo.com also dd3 and rps 10 available.

what's wrong with my les paul??? when i touch any metal parts (including the strings) on my les paul, it makes this tiny little popping noise... it's annoying as hell!!!!! anyone go through this problem??? i don't know what's wrong with it!!

How do you guys feel about artifically aging guitars. I see a lot of vintage or Murphy aged Les Pauls that sure do look pretty. I'm not talking about aging like having finish removed in spots or gouging....like an SRV strat, just light to medium finish checking and having a nice patina to the hardware and finish.

locrian anyone???
if anyone could help me use this mode to make an acceptabe sound it would be much apeciate.

Hi gang. I'm a newbie here although I've been posting on the Fender Discussion page for a long time.

Does anyone know what value resistor I could use to cut a pup's output in half?

i have a dsl100 modded by voodoo amps. Played a show last night amp was fine. Tonight, i was at band practice and my amp was fine intill about 2 hours into it. I picked my guitar back up turned the volume up and the sound was horrible and real faint. Hit the distortion and it became a little louder not even close to where it should have been and sounded reall bad again. I swapped guitars and cords. Still the same, i have a g-major effects processor in the effects loop and the level into the effects processor was lower then normal. I removed the processor to narrow it down more... still the same.

How can I find out information about my friend's stratocaster with the serial number? It's serial number is Z2219463. Thanks guys.

is it possible to wire a H-H, 3-way guitar so that the middle selection kills the guitar completely? My friend saw my guitar and demanded I work on his. All help is appreciated!

Hi guys I'm gonna make a top 10 shred pickups section in the tech corner of my site Shredaholic, and I thought where better to turn to for advice