software

As originally posted at the Jemsite forum, where no one has yet been able/willing to provide a simple yes or no (or indeed any response at all)...The situation:

My best friend's favourite guitar has always been Yamaha's pseudo-RG RGZ321 model, so when I found an extra cheap used one in good shape I decided to surprise him with it for Christmas. (Well, we live a few states apart, so it will be more of a New Years Eve gift than a Christmas gift.)

I've taken it upon myself to address all the minor little complaints he's had about the RGZ over the years, and am well on my way to replacing all the silver hardware with black, installing his fave Duncan pickups, etc. I had planned to replace the stock TRS-101 with a spare Lo-TRS2 I already had around the house, then permanently double block it front and back with solid wood inserts to give him the fine-tuneable fixed bridge feel he's always wanted (but without having to do any filling, routing, or refinishing!).The product:

At what is quickly becoming the last minute, I became aware of the D07 quot;Fastloaderquot; single-locking trem sold (if not manufactured?) by GuitarFetish.com .

from : localhost/store.guitarfetish.com/blflroflotrs.html

I figured, hey, why not go one better and make it so my friend not only has a fine-tuneable fixed Floyd, but one that doesn't require ball-snipping as well? Sure, single-locks (and TRSs) are crap trems, but I'll be blocking the heck out of this one, so no worries.The problem:

I've spent the better part of 48 hours unsuccessfully searching the internet (including Jemsite's forum archives) for an answer to the question below, which I sent to GuitarFetish but haven't received a proper reply yet...

***

gt;gt; Will the D07's post spacing match that of an
gt;gt; Ibanez/Yamaha style TRS-101 or TRS-Pro, or will
gt;gt; would the studs need to be repositioned? gt; 2 7/8quot; stud spacing- so if that's what you got then
gt; it should be a good fit It would be going in a Yamaha guitar that normally takes Takeuchi TRS-101 or Lo-TRS trems, which have stud spacing of 74mm (the same as most Ibanez RGs, from what I've read). 2 7/8quot; would be 73.025mm and 2 15/16quot; would be 74.612mm, so it's neither here nor there.

Since your listing for the D07 says, quot;I've put these on a freakin stadium full of Ibanez RG and Jackson/Charvel guitars- dead easy- on some I need to trim the top route justa hair- but like 1-2mm that's it- Everything else is STOCKquot; , I was hoping to find out if 74mm is generally considered the nearest-round-number metric equivalent of ' stock Gotoh/Floyd 2 7/8quot; ', or if the two sizes are, as my father used to say, 'close enough for government work'.

***Any thoughts, lads and ladies? Is Takeuchi's 74mm the same as Gotoh's 2 7/8quot;, or at least close enough for a non-trem trem? I'm not concerned about the cavity routing, only the post/ stud/ pivot spacing. 74mm spacing functionally equivalent to 2 7/8quot; spacing: yay or nay?

Ta!

74 millimeter = 2.9133858 inch [international, U.S.]

2 7/8quot; = 2.875

2.875 inch [international, U.S.] = 73.025 millimeter

Its darn close but I don't know if lt;1mm difference will make a difference or not. It should hit the posts close enough and a little dremel work might help to tighten up the seating but I've never tried it personally. If it were my project and I was blocking the bridge anyways I'd make him cut off ball ends.

You're a cool friend.

Should work just fine


Originally Posted by ZerberusShould work just fine

Hahaha! Nice avatar man!